InventionsEngine Cooling – Why (Rocket) Engines Don’t Melt

Engine Cooling – Why (Rocket) Engines Don’t Melt

-

- Advertisment -

Gases inside an engines combustion chamber can reach ~3,500 K – which is about half as hot as the surface of the Sun – certainly above the melting point of most materials. Engines need to reach this temperature in order to function correctly, but how can they survive this? In this article you will learn about engine cooling methods used to keep rocket engines from melting.

rocket engine combustion chamber temperature scale
A temperature scale comparing different temperatures to the temperatures inside of a rocket engine’s main combustion chamber. (Credit: Everyday Astronaut)

YouTube video

Heat Sink

At the top of a combustion chamber sits the injector face. Here, the fuel and oxidizer are pumped into the chamber at extremely high pressures. The fuel and oxidizer mix inside the chamber and begin to ignite. As long as the flow continues, the propellants will continue to combust and ignite. But how do the metal chamber walls not melt as the hot gas passes through?

rocket engine injecor face fuel oxidizer mixing propellant, graphic
A render of an injector face of an engine. Here propellants mix and combust in the mein combustion chamber releasing incredible amounts of heat energy. (Credit: Everyday Astronaut)

One option could be to make the walls thick, so much so that the hot gases can’t heat up the thick layer of metal enough to melt it. Here the walls act as a heat sink – that is a large thermal conductor, which is capable of handling high heats for a period of time before all the metal reaches boiling point. An exotic material, one that can handle high heats and stay strong, like inconel or another alloy, could be a good option for this.

However, heat sinks have several major limitations. One limitation is weight. Weight reduction is extremely important when building a rocket, and an additional thick metal wall is going to add a lot of extra weight. Another issue is that an engine will only be able to run for so long before all of the metal eventually reaches its melting point.

heat sink rocket engine cooling, graphic
A render of an engine that only utilizes heat sink cooling. No method of cooling is used other than thick enough engine walls that can endure the heat of the combustion. (Credit: Everyday Astronaut)
- Advertisement -

This means that heat sinks are not a great option for main propulsion engines, which need to run continually for several minutes. However, they could be a viable option for smaller engine types like maneuvring thrusters. Maneuvring thrusters run for a much shorter time than the main propulsion engines, and are often pulsed, giving the engine an opportunity to cool down in between pulses.

Fuel Oxidizer Ratio

Another option to keep an engine from melting is to run the engine in a fuel rich or oxidizer rich configuration, which will lower the temperature of the main exhaust. This ratio is known as the fuel to oxidizer mass ratio.

If someone wanted to burn all of your propellant and have all of it react with each other, you need to burn it at their stoichiometric ratio. Stoichiometric ratio is where the complete amount of fuel and oxidizer perfectly react with each other so no propellant is left unburnt. This means that each atom of each molecule will react with one other atom for complete combustion. The result of this is that you release the maximum amount of heat from the chemical bonds as possible, which would be great in some situations, but not when dealing with rocket engines. The more heat a rocket engine produces, the more you will have to cool your engine so it doesn’t melt, which is not ideal.

fuel to oxidizer mass ratio engine cooling, temperature at stochiometric ratio, graphic
A graphic of the fuel to oxidizer mass ratio if fuel and oxidizer would be burnt at the stoichiometric ratio, resulting in extremely high temperatures that would destroy an engine. (Credit: Everyday Astronaut)

This means that rocket engines have a fuel to oxidizer ratio slightly off from stoichiometric. An engine’s main combustion chamber will tend to run fuel rich as this will have a lower thermal load and have high efficiency.

You could also run the pre-burner or gas generator fuel rich to keep it cool, which is important as it is extremely hard to cool a spinning turbine. The turbine will have a set amount of heat that it can take based on its materials, so the fuel oxidizer ratio needs to change to be suitable. Turbines can be designed to run fuel or oxidizer rich, like the Space Shuttle’s RS-25 main engine, which ran fuel rich, or the soviet designed NK-33 engine, which ran oxidizer rich propellant through their closed cycle pre-burners.

Ablative Cooling

- Advertisement -

Ablative cooling is one of the most simple and effective ways of cooling an engine. This method uses a material which will vaporize and then get thrown away, taking the heat with it. This is usually made out of carbon composite which has an extremely high melting point.

This is the same method that most spacecraft use for heat shields. When a spacecraft re-enters the atmosphere it gets very, very hot. The heat shield takes this heat, and when it’s surface gets too hot, it melts a layer away, taking the heat with it. This stops the heat from penetrating deeper into the spacecraft.

ablative engine cooling, carbon composite layer, combustion chamber, graphic
A carbon composite layer that acts as an ablative layer which insulates the metal walls of the main combustion chamber and absorbs heat when it sublimates away. (Credit: Everyday Astronaut)

This same principle can be applied to cooling a rocket engine. Inside the walls of the combustion chamber and nozzle is a layer of carbon composites. When the propellant is burning in the engine, this carbon layer will slowly be burnt off. This method has no moving parts and is self-regulating, which makes it an extremely efficient and reliable method for cooling engines.

But there are some limitations, most obviously that an engine cooled this way can’t be reused. Some engines won’t even be able to go through full testing before being used as it wears down the ablative chamber walls. Most famously, the Apollo Lunar Ascent engine couldn’t be test fired as a complete unit until it was fired on the surface of the moon to take the astronauts home!

ablative engine cooling, throat widening, expansion ratio, graphic
Ablatively cooled engines will over time open up the throat of the engine due to wearing away more and more of the ablative layer, resulting in lower performance over time.

There are a couple of other examples of ablatively cooled engines, including SpaceX’s first Merlin engine, the Merlin 1A, which flew on the first two Falcon 1 flights, and United Launch Alliance’s Delta IV engine, the RS-68A. It is easy to see that the RS-68A engine is ablatively cooled as it runs on hydrolox, which has a completely transparent exhaust of water vapor – the same as the space shuttle. However, the RS-68 has a bright orange exhaust due to the carbon which is ablated and ejected from the engine as it continues to react with the oxygen in our atmosphere.

- Advertisement -

Another type of small engines, reaction control thrusters, can also use ablative chambers, as this type of engine is only used for a short duration and has a set amount of propellant it can burn through before running out. This means engineers can design the thickness of the wall to match the maximum use.

Regenerative Cooling

Regenerative cooling is the most common way to stop a liquid fueled rocket engine from melting. This method entails flowing some or all of the propellant through the walls of the combustion chamber and nozzle before going through the injectors and into the chamber. While the walls and nozzle of rocket engines look thin, there are actually small channels in the walls, which fuel can be run through in order to keep them cool.

regenerative engine cooling, graphic
Regeneratively cooled engines pump propellant through thin channels inside of the engine’s walls, absorbing heat conducted through the metal walls from the main combustion chamber and the nozzle. (Credit: Everyday Astronaut)

The discovery of this was a major breakthrough, as this method allowed rocket engines to run more or less indefinitely. The early versions of regeneratively cooled engines have a main chamber and a liner on the outside of the engine, where the coolant or fuel could run through. After this, it was normal to see pipes used as the walls of the combustion chamber. An example of this is the RL-10 engine, which still uses a brazed tube construction.

A more common practice today is to cut a cooling channel in the wall of the nozzle, then use a copper or nickel alloy to seal it off, which then will be the inner wall of the chamber. Copper and nickel alloys are used here because of their high thermal conductivity, which allows them to transfer heat from the wall into the coolant.

SpaceX Starship SN8 landing burn failure, engine rich exhaust, green burning copper
Starship SN8 during its landing burn where it experienced low fuel tank pressure resulting in an oxygen rich combustion (closer to the stoichiometric ratio), which effectively eats the inner walls of the engine away burning the copper lining (green flame). (Credit: Everyday Astronaut)

This method means that the fuel can boil before reaching the chamber. This process can sometimes be used to spin the turbine to run the pumps of the engine – this is the expander cycle. The cycle harnesses energy from the thermal expansion of the fuel going from liquid to gas to spin the pumps.

The majority of engines use fuel as their coolant, but oxidizer is also an option. When a cryogenic propellant is used, the outside of a rocket nozzle will be extremely cold, while the inside of the wall will be extremely hot.

One of the main challenges with regenerative cooling is that the pressure inside the walls has to be higher than the pressure of the combustion chamber. This is due to the walls simply being tubes that feed the injectors, and as pressure always flows from high to low, the injectors need to have higher pressure than the combustion chamber.

With an extreme amount of pressure inside tiny walls, it is easy to imagine that a leak could happen. Luckily, because the pressure inside the wall is higher than the pressure in the chamber, if there were a leak it would just provide extra cooling due to film cooling.

Film Cooling

The next common method of engine cooling is film cooling. This method is where a fluid is injected between the combustion chamber and nozzle surface, and the hot combustion gases. As fluids are either gas or liquid, this can be done with liquid or gaseous propellants. The purpose of this is to create a boundary between the wall and the hot combustion gas, which will act as thermal insulation with a cooler fluid in between them.

Film cooled rocket engine, fuel rich propellant injected at the outer perimiter of the injector face, graphic
A film cooled engine in which more fuel rich propellants are injected into the outer perimiter of the injector face to create an insulating layer of unburnt fuel (lack of oxidizer) between the inner combustion chamber and the combustion chamber walls. (Credit: Everyday Astronaut)

The easiest way to do liquid film cooling is to have a higher concentration of fuel or oxidizer injectors on the outer perimeter of the injector face. As the main combustion chamber is fuel rich, fuel is usually favored – there will be a ring of extra fuel flowing around the outer perimeter that won’t have the right amount of oxidizer needed to react with. This means there will be a ring of fuel rich combustion to stop the heat from transferring from the main combustion gases to the walls.

The majority of the fuel close to the wall that won’t react due to the lack of suficient oxidizer essentially runs along the walls of the chamber as a film, between the combustion gases and the chamber walls. However, it will probably phase change from a liquid to a gas, creating a vapor boundary layer, which will continue to absorb heat as the process of changing phases absorbs a certain amount of heat.

Film cooling of a rocket engine, throat hotspot film cooling, graphic
A regeneratively cooled engine that also uses film cooling in hotspots like the throat of the engine where propellant is injected into the throat to lower the thermal load. (Credit: Everyday Astronaut)

It is also common to drill holes into the wall (provided they are regeneratively cooled) and leak in a small amount of liquid fuel, specifically in hotspots like the throat of an engine.

A benefit of using fuel as coolant is that it creates a carbon layer, in the form of coking, along the walls when a carbon based fuel like RP-1 is used. In fuel rich combustion, a lot of carbon is left unburnt and can create soot. You can see this in the exhaust of the gas generator for the Merlin engine. In this engine, SpaceX runs the gas generator extremely fuel rich, which reduces the temperature enough to stop the turbine from melting. The result of this is a very dark and sooty exhaust. This soot can also stick to the inside walls of the chamber. It is not great if the soot sticks to the injectors and the cooling holes, but the soot which sticks to the walls can act as an additional thermal barrier.

Tom Markusic, CEO Firefly, soot on face
Tom Markusic, CEO of Firefly, with soot on his face that came from the inner walls of their Reaver engine acting as an insulating layer, which helps reducing the overall heat load. (Credit: Everyday Astronaut)

The exhaust gas of the Merlin engine’s gas generator can also be used to film cool some of the nozzle. This doesn’t happen on the sea level Merlins, where the exhaust is just dumped overboard, but it does happen on the vacuum optimized Merlin. Here, the turbine exhaust gas gets pumped into the nozzle extension, which optimizes the engine for vacuum conditions. As the nozzle expands after the throat, the exhaust gas gets cooler and has a lower pressure the further down the nozzle you travel. When pumping in the turbine exhaust gas, it needs to be done far enough down the nozzle where it has a higher pressure than the main combustion exhaust pressure, but also at the point where the heat needed to protect the nozzle can successfully be insulated by the film cooling of the turbine exhaust gas as regenerative cooling is often terminated at that point.

This doesn’t only happen on the vacuum optimized Merlin, but has been done on both of the engines on the Saturn V. The F-1 and the J-2 both used turbine exhaust film cooling to keep the lower portions of their nozzles cool. While the J-2 still used regenerative cooling below the manifold, the F-1 stopped doing regenerative cooling at the manifold as film cooling was enough to stop the rest of the nozzle from melting.

The effect of this was visible when the F-1 engines were running. The bright orange flame front didn’t start at the end of the nozzle, there instead is a dark part between the flame and the nozzle exit – this is the film cooling turbine exhaust. Because of it being so fuel rich, it takes a moment for it to find oxygen to burn with and ignite, which doesn’t happen until it has left the engine and can start to react with oxygen in the atmosphere.

Radiative Cooling

Both SpaceX’s vacuum Merlin engine and Rocket Lab’s vacuum Rutherford engine glow bright red when powered, because the metal gets really hot and radiates the heat out into space. As there is no atmosphere in space, there is no air to pick up and conduct or convect heat away. Instead, engines can radiate heat away from their nozzles, as radiation doesn’t require matter to transfer heat – like the Sun that transfers heat through the vacuum of space via radiation.

The nozzle extensions in the vacuum optimized Merlin and Rutherford engines are made from a very thin metal, usually an alloy like niobium alloy, which is able to withstand high heat loads. The downside of these nozzle extensions though is that they are very thin and relatively fragile. Furthermore, niobium is also very reactive to oxygen, which means the engine like this can realistically only operate in a vacuum environment and is also more complex during manufacturing.

Summary

Looking at the Merlin Vacuum engine is perhaps the best way to summarize methods of engine cooling, as this engine employs almost every type of cooling. 

The gas generator uses both a heat sink and a very fuel-rich exhaust. This is done as the other types of cooling can’t be used for a spinning turbine. In this situation, engineers just have to use high temperature tolerant metals and lower the exhaust temperature so that the metal can handle the heat. 

Regenerative cooling is used for cooling the chamber walls, throat and the first section of the nozzle, and for the inside of the engine, some film cooling is done. Film cooling with the gas generator exhaust at the nozzle extension is utilized when the regenerative cooling channels end. Additionally, the nozzle extension also radiates additional heat away by glowing bright orange using a niobium alloy.

The vacuum optimized Merlin engine doesn’t appear to use ablative cooling, but as the upper stages are only used once, the engine could probably even have used ablative cooling if it were necessary.

NOW WITH OVER +8500 USERS. people can Join Knowasiak for free. Sign up on Knowasiak.com
Read More

- Advertisement -
Ava avatar
Avahttps://facebook.com/avamax
I'm a researcher at Utokyo :) and a big fan of Ava Max

You might also likeRELATED
Recommended to you

Our Rails test suite runs in 1 minute on Buildkite

At PlanetScale, our backend API is built with Ruby on Rails. It's a pretty standard Rails application. We use...

Why Wolfram Tech Isn’t Begin Source

Over the years, I have been asked many times about my opinions on free and open-source software. Sometimes the questions are driven by comparison to some promising or newly fashionable open-source project, sometimes by comparison to a stagnating open-source project and sometimes by the belief that Wolfram technology would be better if it were open…
- Advertisement -

Thich Nhat Hanh, Vietnamese Zen Master, Dies at 95

Thich Nhat Hanh at the Plum Village monastery in southern France | Courtesy Plum Village Community of Engaged Buddhism Vietnamese Zen Master Thich Nhat Hanh—a world-renowned spiritual leader, author, poet, and peace activist—died on January 22, 2022 at midnight (ICT) at his root temple, Tu Hien Temple, in Hue, Vietnam. He was 95. “Our beloved…

Before wave of train thefts, Union Pacific laid off some of its police force

News organizations both locally and nationally have been covering the rise of cargo theft in L.A.’s northeast train tracks in the past few days. Anchors on morning news have been quick to point out that there have been over 100 arrests, and even Forbes have been quick to point out the staggering $5 million worth…

Must read

In Response to My first impressions of Web3

Both gave me a feeling for how the space works. To be clear, there is nothing particularly “distributed” about the apps themselves: they’re just normal react websites. The “distributedness” refers to where the state and the logic/permissions for updating the state lives: on the blockchain instead of in a “centralized” database. Just to clarify, this…

YouTube is testing people now?

I never get these. I do get ads but sometime somewhere I opted out of personalization. YouTube tried to scare me with a warning saying I would no longer get ads related to my interests. Didn’t work. The ads I get are really fascinating because they are all over the map. I learn stuff about…
- Advertisement -